Instructions for the inspection controller in production. Job description of the control master of the technical control department. Job and general responsibilities

Regardless of the product being manufactured, there must be an employee at the production site who constantly monitors the technical process and its compliance with GOST. This profession is called quality control inspector. He monitors all stages of production, from the supply of raw materials to the storage of finished products. A controller can be any employee who is responsible for supervision and quality control.

Responsibilities of the controller

The main task of the controller is to prevent manufacturing defects, so he is obliged to regularly monitor:

• the quality of raw materials and production recipes;
• check the quality of production equipment;
• monitor the quality of employee work;
• promptly stop the process during the release of defective products;
• eliminate the causes of its occurrence;
• monitor the correct operation of the equipment;
• compliance of production with technical documentation and state standards.

The quality control inspector is personally responsible for low-quality products and for their return to the factory. That is why highly qualified people who have received appropriate education are hired for this position. Experience, personal qualities and good knowledge of the entire process of manufacturing goods allows us to simultaneously monitor several processes and minimize the presence of defects.

What should a controller know?

The job of a quality control inspector is very responsible. In addition to monitoring all processes at the factory, he must know all the technical documentation so that the products fully comply with them. Knowing what reasons can lead to defects, an employee of the technical control department is engaged in prevention and elimination of them. After the product has been released, he checks it for suitability. If there is a defective product, the appropriate form is filled out, which states the reasons for its occurrence, those responsible for this, and the write-off of the goods is issued. Here are some other responsibilities of a quality control inspector that he should know:

• standards for raw materials, finished products;
• types and sizes of semi-finished products and finished products;
• technological process;
• ability to use measuring instruments;
• safety regulations, sanitary standards;
• organization of work in the workplace;
• types of defects and methods for eliminating them.

All this allows the employee to visually see during the production process how well the product meets the standards.

Personal characteristics

The physical load when working as a quality control inspector is insignificant, but other important personal qualities are required. He must have good memory and vision, be collected and attentive. Professional quality:

Important factors when hiring

To obtain the position of quality control inspector, you need:

• presence of higher specialized education;
• experience in the field of production control;
• excellent knowledge of modern technologies;
• ability to use a computer and electronic documents and programs;
• drawing up production plans and documents;
• endurance and ability to perform several tasks simultaneously, monitor several processes;
• Responsible attitude towards performing basic job duties.

Job responsibilities will depend on what area of ​​activity the employee specializes in.

Relationships with other departments

The quality controller actively cooperates with all departments and workshops of the factory. Identification of the causes of defects is carried out together with the heads of workshops. When raw materials arrive, the supply department informs the quality control department about this, providing documents from the supplier for control. All products in the warehouse, their import and export are controlled by the quality department and are documented with the relevant acts. Work orders are also signed by a specialist, on the basis of which wages are calculated in the accounting department. Everything that the quality control inspector does is interconnected with the work of all production departments.

Advantages of the profession

The main advantage is the demand for specialists in the labor market. Controllers are needed everywhere, and areas of activity are constantly expanding, new specializations are emerging. The work does not require physical training, so people of any age can master it.

Education

You can learn to become a controller at a vocational school or other educational institution that corresponds to the field of activity in which the employee will work. Having completed training at a vocational school, a graduate receives a 2-3 grade and the opportunity to continue his education or get a job. Some factories organize individual training courses with the opportunity to complete an internship at their plant.

V.V. Umnikov

senior control foreman of the technical control department

1. General Provisions

1.1 The senior control master of the technical control department of OJSC "Company" reports directly to the head of the technical control department of OJSC "Company" or the head of the technical control bureau, if this position is provided.

1.2 The senior control foreman is appointed and dismissed by order of the General Director of OJSC "Company" on the recommendation of the Deputy General Director for Quality and Metrology or the Head of the Quality Control Department.

1.3 A person with a higher professional (technical) education and work experience in production of at least 1 year or a secondary technical education and work experience in a specialty in the relevant industry profile for at least 3 years is appointed as a senior inspection master of the quality control department.

1.4 The following are subordinate to the Senior Control Foreman:

— testers of subordinate departments:

1.5 The senior control master in his activities is guided by:

- resolutions of government bodies of the Russian Federation;

- Law of the Russian Federation “On Technical Regulation”;

— Law of the Russian Federation “On Standardization” No. 5154-1 of June 10, 1993;

— Law of the Russian Federation “On Certification of Products and Services” No. 5151-1 of June 10, 1993;

— Law of the Russian Federation “On ensuring the uniformity of measurements” No. 4871-1 of April 27, 1993;

— The company’s quality policy;

— documentation of the enterprise’s quality management system;

— methodological, regulatory and technical documents and international standards;

— Regulations on quality control department;

- this job description.

1.6 In case of temporary absence, the duties of the senior control foreman are performed by a specialist appointed by order of the General Director on the recommendation of the head of the quality control department.

2 Job responsibilities

The senior control master is obliged to:

2.1 Organize work at the assigned site to control and improve product quality, completeness of manufactured products and accounting for non-conforming products.

2.2 Monitor the correctness of establishing the type and type of product, its compliance with approved samples (standards), standards, technical specifications and other regulatory and technical documentation.

2.3 Monitor compliance with technological processes at all stages of production, instructions and methods for technical control at workplaces, quality of containers and packaging, technical condition of equipment, storage of raw materials, materials and semi-finished products, components, finished products.

2.4 Manage the preparation of technical documentation certifying the quality and completeness of manufactured or supplied products (passports, certificates), product certification.

2.5 Monitor compliance with schedules for checking the accuracy of production equipment and fixtures, the condition of control and measuring equipment, their availability at workplaces, and timely submission for state inspection.

2.6 Take measures to prevent the production of products that do not meet established requirements, identify the causes and culprits of nonconformities, as well as develop and implement measures aimed at improving the quality and competitiveness of products.

2.7 Participate in the development and implementation of the most advanced product quality management systems, control methods, new and revised current standards, technical specifications and other standards and instructions.

2.8 Monitor compliance by subordinates with labor protection rules, safety regulations, production and labor discipline, and internal labor regulations. Conduct periodic training on labor protection and safety regulations.

2.9 Monitor the delivery of finished products to the warehouse.

2.10 Make proposals to the head of the quality control department on encouraging employees, as well as bringing to disciplinary liability violators of production and labor discipline.

2.11 Promote the improvement of qualifications and professional skills of workers, their training and assignment of ranks, and carry out educational work in the team.

2.12 Participate in production meetings held by the heads of production departments of the enterprise.

2.13 Participate in the preparation and holding of the “Quality Day” in the workshop.

2.14 Timely and accurately execute production orders of the general director of the enterprise, production tasks, instructions and orders of the deputy general director for quality and metrology, head of the quality control department.

2.15 Perform job duties provided for in this job description and the employment contract.

2.16 Comply with the internal labor regulations established at the enterprise.

2.17 Do not engage in activities directly or indirectly detrimental to the interests of the enterprise.

2.18 Know the relevant QMS documentation required for the work and comply with its requirements.

2.19 Constantly improve the results of your activities.

3 Professional requirements

The senior control master must know:

— legislative and regulatory legal acts, methodological materials on product quality management;

— technological processes and production modes;

— basic technological and design data of manufactured products;

— technical and economic requirements for raw materials, materials, semi-finished products, components and finished products;

— current industry and enterprise standards, technical conditions, quality standards, technological instructions;

— systems, means and methods of technical control of production;

— rules for acceptance and storage of finished products, raw materials, materials, semi-finished products, components;

— sampling methods, procedures for labeling and packaging of products;

— procedure for certification of the quality of industrial products;

— types of production nonconformities, methods for their prevention and elimination;

— rules for testing and acceptance of products;

— the procedure for preparing technical documentation certifying product quality;

— fundamentals of economics, organization of production, labor and management;

— basics of labor legislation;

— rules and regulations of labor protection;

— relevant QMS documentation.

The senior control master has the right:

4.1 Request and receive information necessary for him to perform his official duties from employees of any departments.

4.2 Make decisions on disagreements between quality control department employees and employees of production departments of the enterprise in their assessment of product compliance with the requirements established for it.

4.3 Submit proposals to the Deputy General Director for Quality and Metrology - Head of Quality Control Department on bringing to justice officials and workers of the enterprise guilty of manufacturing products that do not meet established requirements.

4.4 Give production instructions and orders that are binding for the quality control department employees subordinate to him.

4.5 Make proposals to the Deputy General Director for Quality and Metrology - Head of the Quality Control Department on rewarding and punishing employees subordinate to him in the prescribed manner.

4.6 Demand that shop managers establish the causes of non-conformity of products, punish those responsible for their occurrence, as well as persons who violated the production technology established by the documentation.

4.7 Use the benefits established by the legislation of the Russian Federation and provided for employees in the collective agreement of the enterprise.

4.8 To provide him with the working conditions necessary to perform his official duties.

4.9 Represent the company in third-party organizations on issues of product quality.

4.10 Represent the quality control department in various commissions of the enterprise on issues within its competence.

5 Service relationships

The senior control master of the technical control department interacts with:

5.1 With the central laboratory of measuring technology:

— provides: applications for high-precision and arbitration measurements and tests. Measuring instruments for verification, according to the schedule, failed before the next verification. Measuring instruments for rechecking or repair;

— receives: schedules for checking measuring instruments. Information on the withdrawal from circulation of faulty measuring instruments that did not pass inspections within the established time limits.

5.2 With workshops and areas:

— provides: a conclusion on the compliance of products with technical requirements. documentation (specifications, GOSTs, drawings, standards, manufacturing technology);

— receives: accompanying technical documentation (drawings, diagrams, standards and manufacturing technology for products).

5.3 With the quality engineer of the technical control department:

— provides information about the products presented and any discrepancies found. Acts of non-compliance indicating those responsible for the manufacture of non-conforming products. Information about the production culture;

— receives: information about product returns for each day. Information on the results of accounting for losses from non-conforming products in workshops based on acts of non-compliance and on attributing the amounts to those responsible.

The senior control master is responsible in the manner established by the laws of the Russian Federation for:

— failure to fulfill the duties assigned to him, provided for by this job description and the employment agreement (contract);

Materials: http://oformitely.ru/doljnostnaya_instrukciya_starshego_kontrolynogo_mastera_otk.html

Quality Control Controller

Safety Inspector The subject of concern for the employees of the technical control service of the enterprise is to improve the quality of all types of products, ensuring that their indicators comply with the level of world achievements.

Quality indicators include dimensional accuracy, operational reliability, ease of use, compliance with GOSTs, and aesthetic requirements. ControllersQuality Control Department(technical control department) is a mass working profession. It ranks 4th in terms of the number of specialists employed in industry.
Main operation at work controller— comparison of product parameters with the indicators specified in GOSTs, drawings, technological documentation. In this case, products are inspected “by eye” or checked using control and measuring instruments, devices: micrometers, calipers, gauges, magnifiers, microscopes, electrical measuring instruments, etc. By means of labor controller There are also lists of “standard images” of the required characteristics of quality products, stored in his memory.
Controller receives a batch of finished products or semi-finished products, checks each of them, affixes a control stamp, draws up accompanying documentation, defective statements. But controller not only identifies defects, but also studies its causes and suggests measures for its prevention. The reasons may be different: poorly adjusted equipment, poor-quality materials, defects in workpieces, unskilled workers, negligence, and inattentiveness of workers. To the controller one must be attentive and correct and, at the same time, demanding and principled in communicating with workers.

Job description of product quality and technological process controller, 7th category

Authoritative controller disciplines workers. Inexperience, carelessness controller may cause conflicts and disorganize work on the site. Controller- a quality expert, he must be conscientious and understand the consequences of delivering low-quality products. Job controller is associated with the performance of monotonous actions and may seem monotonous to people who prefer a quick change of impressions and actions, who are mobile. Job controller requires accuracy and thoroughness, so thorough, unhurried people work more successfully here.
Skilled controller knows production technology well, the work process itself, understands drawings, knows how to use control and measuring instruments, has a developed memory, normal vision (not lower than 0.5, without pronounced anomalies), stable visual performance, noise immunity, composure, attentiveness. Exercise stress controller insignificant.
Controllers work in specially equipped workplaces in good lighting. Salary depends on qualifications, time-based bonus.
Speciality controllerQuality Control Department has much in common with the work of a tester of finished products or semi-finished products, a commodity expert.
Profession controllerQuality Control Department can be purchased at the enterprise through individual-team training or at a vocational school. A vocational school graduate receives 2-3 rank. In the future, you can continue your education at a technical school or university corresponding to the production profile, become an inspection foreman, the head of a workshop inspection service, or the head of an enterprise’s technical inspection department.

The technical control department (QCD) exists at production enterprises for the timely detection of violations in production technology. The quality control inspector is responsible for identifying defects in the manufacture of products and checking product compliance with standards and GOSTs.

Job Description for Product Processing Quality Controller

Control is carried out visually or using instrumentation.

Vika works in the quality department of a Russian-Japanese car painting company. The working day at production begins at 7:15, Vika must be at work at 8 in the morning (a bit early, but at least you can go home at 16:15). At approximately 8:15 the daily planning meeting takes place - the entire quality department (20 people) gathers. In 15 minutes, the boss distributes tasks and discusses current problems.

If the beginning of the working day is the same, then the rest of the day goes differently. Time may be spent testing the quality of paint or primer, checking paint colors and discussing future orders with suppliers (for example, coordinating colors), drawing up reports (sometimes this takes many hours), calibrating instruments (usually done monthly ) and other tasks.

Places of work

The position of quality control inspector is required at all manufacturing enterprises.

Each product must undergo quality control before going on sale.

History of the profession

The profession of quality control inspector can be said to have appeared thanks to Henry Leland, who made weapons production at the factories of Samuel Colt a role model. The “Master of Precision” introduced the concept of “pass caliber” into use and for the first time in history began to reject outwardly suitable shells due to their non-compliance with the standard. His motto: “Craftsmanship is the credo, accuracy is the law,” is followed by the world’s most successful manufacturers.

Responsibilities of the Quality Control Controller

The job responsibilities of a quality control inspector include:

• Output control of finished goods.
• Verification of actual parameters of manufactured products with reference indicators specified in technical documentation, drawings, GOSTs.
• Preparation of accompanying documentation - certificates, defective statements, quality certificates.
• Checking the quality of the raw materials used.
• Identification of technological inconsistencies and causes of defects.
• Promotion of ideas for modernization of production.

Sometimes the functions of a quality control inspector may also include working with complaints (customer complaints).

Requirements for a quality control inspector

The basic requirements for a quality control inspector are as follows:

• Secondary technical or higher education.
• Experience from 1 year.
• Knowledge of production technology, GOST standards.
• Ability to read drawings and design documentation.
• Skills in operating control and measuring instruments.
• Attention to detail.

Sometimes a specialist may be required to have good vision and excellent coordination of movements, as well as additional education (depending on the specifics of the production).

Resume sample

Sample resume for quality control inspector.

How to become a quality control inspector

To become a quality control inspector, it is enough to obtain a secondary technical or higher specialized education. Knowledge of production processes is also necessary, because the specialist communicates with technologists, designers, craftsmen, heads of production departments and the sales department. Knowledge of production often comes with experience as either a technologist or a technical control controller.

Quality Control Controller Salary

The salary of a quality control inspector ranges from 25,000 to 45,000 rubles. As you move up the career ladder, your salary increases significantly. An inspection foreman can receive a salary of up to 65,000 rubles, and the head of a workshop inspection service can receive up to 85,000. The average salary of a quality control inspector is 30,000 rubles.

Job description of the control master of the technical control department [name of organization, enterprise, etc.]

This job description has been developed and approved in accordance with the provisions of the Labor Code of the Russian Federation and other regulations governing labor relations in the Russian Federation.

I. General provisions

1.1. The control foreman of the technical control department (bureau) in his activities does not depend on the management of the workshop and is directly subordinate to the head (bureau) of technical control (senior control foreman).

1.2. The inspection master is guided in his work by:

— regulations on the technical control department;

— this job description;

— the charter of the enterprise;

- legislation of the Russian Federation.

1.3. Persons with a higher technical education and work experience in production of at least 1 year or secondary specialized education and work experience in production of at least [value] years are appointed to the position of control foreman.

II. Job responsibilities

2.1. Organize the work of inspectors and control the quality of products and services, the completeness of manufactured products at the assigned production site.

2.2. Ensure control over compliance with technological regimes at all stages of the production process.

2.3. Take measures to prevent production and prevent the release of products that do not meet established requirements, identify the causes and culprits of defects, and organize records of defects.

2.4. Carry out work on the preparation of technical documentation certifying the quality and completeness of the supplied products (passports, certificates, etc.).

2.5. Take part in the delivery of finished products and completed work (services) to customers.

2.6. Check compliance with instructions and techniques for technical control at workplaces.

Profession Quality Control Controller

Carry out quality control of containers and packaging at workplaces, the technical condition of equipment and means of transport, storage of raw materials, materials, semi-finished products, components, and finished products.

2.8. Monitor the implementation of schedules for checking the accuracy of production equipment and fixtures, the technical condition of control and measuring equipment, their availability at workplaces and timely submission for state inspection.

2.9. Study and improve technology for monitoring products, materials, and components.

2.10. Participate in events related to the introduction of new and revision of existing standards, technical specifications, quality indicators and instructions.

2.11. Perform work related to product certification.

2.12. Monitor compliance by workers subordinate to him with labor protection rules, safety regulations, production and labor discipline, and internal labor regulations.

III. Rights

The control master of the technical control department (bureau) has the right to:

3.1. Determine the quality of products manufactured at the production site.

3.2. Require production foremen to stop work if defective or defective products appear, as well as in cases of working on faulty equipment or using poor-quality material, and to stop accepting products if these requirements are not met, immediately reporting this to the senior control foreman or the head of the quality control department (BTK).

Identify those responsible for the marriage, which should be reflected in the primary documents.

3.4. Do not accept products presented by the workshop (site) in the absence of established documentation for the work performed and in the absence of a production foreman’s mark confirming his acceptance of the first part.

3.5. Participate in product quality meetings held by the production foreman.

3.6. Prohibit the use of control and measuring instruments that give incorrect readings until the problems are corrected or replaced with suitable ones.

3.7. Represent subordinate supervisors for incentives or penalties.

IV. Responsibility

The control master is responsible for:

4.1. For failure to perform (improper performance) of one’s job duties as provided for in this job description, within the limits determined by the labor legislation of the Russian Federation.

4.2. For offenses committed in the course of carrying out their activities - within the limits determined by the administrative, criminal and civil legislation of the Russian Federation.

4.3. For causing material damage - within the limits determined by labor, criminal and civil legislation of the Russian Federation.

The job description has been developed in accordance with [name, number and date of document].

Head of structural unit

[initials, surname]

[signature]

[day month Year]

Agreed:

Head of the legal department

[initials, surname]

[signature]

[day month Year]

I have read the instructions:

[initials, surname]

[signature]

[day month Year]

The technical control department (QCD) exists at production enterprises for the timely detection of violations in production technology. The quality control inspector is responsible for identifying defects in the manufacture of products and checking product compliance with standards and GOSTs. Control is carried out visually or using instrumentation.

Vika works in the quality department of a Russian-Japanese car painting company. The working day at production begins at 7:15, Vika must be at work at 8 in the morning (a bit early, but at least you can go home at 16:15). At approximately 8:15 the daily planning meeting takes place - the entire quality department (20 people) gathers. In 15 minutes, the boss distributes tasks and discusses current problems.

If the beginning of the working day is the same, then the rest of the day goes differently. Time may be spent testing the quality of paint or primer, checking paint colors and discussing future orders with suppliers (for example, coordinating colors), drawing up reports (sometimes this takes many hours), calibrating instruments (usually done monthly ) and other tasks.

Places of work

The position of quality control inspector is required at all manufacturing enterprises. Each product must undergo quality control before going on sale.

History of the profession

The profession of quality control inspector can be said to have appeared thanks to Henry Leland, who made weapons production at the factories of Samuel Colt a role model. The “Master of Precision” introduced the concept of “pass caliber” into use and for the first time in history began to reject outwardly suitable shells due to their non-compliance with the standard. His motto: “Craftsmanship is the credo, accuracy is the law,” is followed by the world’s most successful manufacturers.

Responsibilities of the Quality Control Controller

The job responsibilities of a quality control inspector include:

• Output control of finished goods.
• Verification of actual parameters of manufactured products with reference indicators specified in technical documentation, drawings, GOSTs.
• Preparation of accompanying documentation - certificates, defective statements, quality certificates.
• Checking the quality of the raw materials used.
• Identification of technological inconsistencies and causes of defects.
• Promotion of ideas for modernization of production.

Sometimes the functions of a quality control inspector may also include working with complaints (customer complaints).

Requirements for a quality control inspector

The basic requirements for a quality control inspector are as follows:

• Secondary technical or higher education.
• Experience from 1 year.
• Knowledge of production technology, GOST standards.
• Ability to read drawings and design documentation.
• Skills in operating control and measuring instruments.
• Attention to detail.

Sometimes a specialist may be required to have good vision and excellent coordination of movements, as well as additional education (depending on the specifics of the production).

Resume sample

How to become a quality control inspector

To become a quality control inspector, it is enough to obtain a secondary technical or higher specialized education. Knowledge of production processes is also necessary, because the specialist communicates with technologists, designers, craftsmen, heads of production departments and the sales department. Knowledge of production often comes with experience as either a technologist or a technical control controller.

Quality Control Controller Salary

The salary of a quality control inspector ranges from 25,000 to 45,000 rubles. As you move up the career ladder, your salary increases significantly. An inspection foreman can receive a salary of up to 65,000 rubles, and the head of a workshop inspection service can receive up to 85,000. The average salary of a quality control inspector is 30,000 rubles.

Where to get training

In addition to higher education, there are a number of short-term training on the market, usually lasting from a week to a year.

The Institute of Professional Education "IPO" invites you to take distance courses in the direction of "" (there are options 256, 512 and 1024 academic hours) to receive a diploma or state-issued certificate. We have trained more than 8,000 graduates from almost 200 cities. You can undergo external training and receive interest-free installments.

I approve

[position, signature, full name.

Manager or other

Official authorized

Approve

[organizational and legal form, job description]

name of organization, [day, month, year]

enterprises] M.P.

Job description

6th category product and process quality controller [name of organization]

This job description was developed and approved in accordance with the provisions of the Labor Code of the Russian Federation, the Unified Tariff and Qualification Directory of Work and Professions of Workers, issue 24, section “General professions of chemical production”, approved by order of the Ministry of Health and Social Development of the Russian Federation dated March 28, 2006. N 208, Order of the Ministry of Health and Social Development of the Russian Federation dated August 11, 2011 N 906n “On approval of the Standard Standards for the free issuance of special clothing, special footwear and other personal protective equipment to chemical production workers engaged in work with harmful and (or) dangerous conditions labor, as well as work performed in special temperature conditions or associated with pollution", Order of the Ministry of Health and Social Development of the Russian Federation dated February 16, 2009 N 46n "On approval of the List of industries, professions and positions in which work gives the right to free receiving therapeutic and preventive nutrition in connection with particularly harmful working conditions, rations of therapeutic and preventive nutrition, standards for the free issuance of vitamin preparations and the Rules for the free issuance of therapeutic and preventive nutrition" and other legal acts regulating labor relations.

1. General Provisions

1.1. A product and process quality controller of the 6th category belongs to the category of workers and is directly subordinate to [name of the position of the immediate supervisor].

1.2. A person with secondary vocational education and work experience in the specialty of at least [value] years is accepted for the position of product quality and technological process controller of the 6th category.

1.3. A 6th category product and process quality controller is appointed to the position and dismissed by order of [name of the manager’s position].

1.4. A 6th category product and process quality controller must know:

State standards and technical specifications for the raw materials used, finished products;

Range of finished products;

Physico-chemical and technological properties of the raw materials used, materials and finished products, state standards and technical conditions for them;

Design, principle of operation of the equipment being serviced, instrumentation used;

Technological regime of controlled processes;

Methods for conducting observations of the technological process;

Rules for sampling, methods of analysis and calculations;

Rules for receiving and processing batches of products;

Rules for storage and accounting of toxic substances;

Instructions on control and procedure for registration of shipped shipments;

Controlled technological process, rules for regulating its technological regime;

A diagram of the serviced area, its fittings and communications;

Design, principle of operation of the equipment being serviced;

Rules for using the control and measuring instruments used;

Methods of mathematical statistics;

Principles of drawing up a diagnostic card;

Technical conditions for the acceptance of complexly configured plastic and rubber products;

Rules for maintaining control charts and drawing up reports;

Methods for testing the raw materials used, components, finished products;

Rules for the preparation of technological documentation;

Design features of particularly complex and precise instruments and installations, methods of their adjustment and alignment;

Fundamentals of metrology and radio engineering;

Fundamentals of labor legislation;

Internal labor regulations;

Rules of sanitary and personal hygiene;

Labor protection, safety and fire protection rules and regulations;

Rules for the use of personal protective equipment;

Requirements for the rational organization of labor in the workplace;

Requirements for the quality of work (services) performed;

Types of defects and ways to prevent and eliminate them;

Production alarm.

2. Job responsibilities

The 6th category product and process quality controller is assigned the following job responsibilities:

2.1. Monitoring the quality of products and the progress of the technological process in the serviced area according to the readings of instrumentation and analysis results.

2.2. Reception of product batches from the workshops.

2.3. Quality control of plastic films on special installations with the elimination of identified defects.

2.4. Conducting operational control of semi-finished and finished products.

2.5. Conducting analyzes of products and raw materials, issuing conclusions on the compliance of product quality, packaging and labeling with the requirements of state standards and technical conditions and permission for shipment.

2.6. Interoperational quality control of products for export and special products.

2.7. Maintaining a log of product grades with classification of defects.

2.8. Registration of acts for non-grade products.

2.10. Monitoring compliance with the technological regime in the serviced area.

2.11. Monitoring timely and correct sampling.

2.12. Assessment of the technical condition of operating equipment.

2.13. Participation in the acceptance of serviced equipment after technological stops, cleaning, and repairs.

2.14. Monitoring the quality of products and the progress of the technological process using control charts, network charts and technical control charts.

2.15. Processing of technological and analytical data using the method of mathematical statistics.

2.16. Providing information to the shift foreman (shift manager) about the progress of the technological process and deviations of its parameters from the specified values, and, if necessary, issuing a warning signal.

2.17. Product quality control, separation of parts of products that have defects.

2.18. Monitoring the correct sorting of products into batches and assortments.

2.19. Inspection and acceptance in accordance with design documentation and technical specifications of complex configurations of products made from various plastics and rubber.

2.20. Inspection and acceptance of small items using magnifying glasses and a microscope.

2.21. Checking the geometric shape and relative position of surfaces, participating in various tests.

2.22. Organization of additional control of the technological process in order to eliminate the reasons that caused its violation.

2.23. Drawing up a diagnostic file that provides possible options for influencing the technological process in case of deviations of its parameters or indicators of raw materials from those established by the norm.

2.24. Selective quality control of sorting in warehouses of finished products and performance of work on quality control of products on sorting conveyors.

2.25. Monitoring the conduct of analyzes and correct storage of products.

2.26. Monitoring the progress of the technological process in accordance with technological regulations.

2.27. Conducting laboratory tests of finished products and semi-finished products to determine their compliance with state standards and technical specifications, design and technological documentation, and drawings.

2.28. Inspection and acceptance of particularly complex plastic and rubber products.

2.29. Carrying out the necessary calculations based on the analyzes, tests and studies carried out, systematizing the results obtained.

2.31. Participation in the implementation of measures to improve product quality and prevent defects, as well as in improving testing and control methods.

2.32. Management of workers of lower ranks of the same profession.

2.33. Carrying out work on acceptance and delivery of shifts, cleaning the workplace, devices, tools, as well as maintaining them in proper condition, cleaning equipment, maintaining established technical documentation.

2.34. [Other job responsibilities].

3. Types of work

A 6th category product and process quality controller performs the following types of work:

3.2. Performing acceptance, periodic and standard tests of magnetic media and technical films (dry film photoresistors) on electronic measuring stands and optical-mechanical installations and instruments.

3.3. Carrying out accounting and analysis of defect-free production of audio magnetic tapes using a computer.

3.4. Conducting electromagnetic, electroacoustic and physical-mechanical tests of magnetic media on particularly complex devices and systems.

The control master is guided in his work by: - ​​the regulations on the technical control department; — this job description; — the charter of the enterprise; - legislation of the Russian Federation. 1.3. Persons with a higher technical education and work experience in production of at least 1 year or secondary specialized education and work experience in production of at least [value] years are appointed to the position of control foreman. II. Job responsibilities 2.1. Organize the work of inspectors and control the quality of products and services, the completeness of manufactured products at the assigned production site. 2.2. Ensure control over compliance with technological regimes at all stages of the production process. 2.3.

Job description of the controller

Job responsibilities of a product processing quality controller The job responsibilities of a product processing quality controller are: a) Special (professional) job responsibilities: - Quality control of product processing at various stages of the technological process. - Return to collection points of products accepted without indicating defects or due to incompleteness of orders. - Checking the correctness of determining the types of technological processing, carrying out preparatory operations and compliance with the rules for completing production batches. - Reviewing products and determining the quality of processing in accordance with current technological instructions, enterprise standards, republican standards and technical conditions. - Selection of products with processing defects and identification of the causes of defects.

Work instructions for the controller of materials, metals, semi-finished products and products

Rights of the product processing quality controller The product processing quality controller has the right to: 1. Submit proposals for management's consideration: - to improve work related to the responsibilities provided for in these instructions, - to bring to material and disciplinary liability workers who violated production and labor discipline.
2.

Request from structural divisions and employees of the organization the information necessary for him to perform his job duties. 3. Get acquainted with the documents defining his rights and responsibilities for his position, criteria for assessing the quality of performance of official duties.

4. Get acquainted with the draft decisions of the organization’s management relating to its activities. 5.

What are the official rights and responsibilities of the controller?

The quality control inspector has the right to monitor the timely and complete fulfillment of production tasks by the enterprise’s employees. This right also implies the opportunity to report to immediate management about violations identified during verification of compliance with the production process and product quality control.

Attention

Also, this employee has the right to report to management about distinguished employees and nominate them for promotion. In the process of carrying out his activities, he has the right to give mandatory instructions to his subordinates and other persons whose activities are under his supervision.

To optimally carry out his own functions, the quality control controller has the right to interact with other services and departments of the company, request the necessary documents and information from other departments, and send them the information received.

Job Description for Product Processing Quality Controller

Stop acceptance and shipment of finished products that do not meet the requirements of GOST, TU, standards, drawings, established completeness and technical documentation, immediately notifying the quality manager.3.3. Make proposals to the quality manager and the head of the quality control department to suspend the manufacturing process of products in individual departments and workshops if they do not comply with standards, specifications, drawings, etc. 3.3.

Request and receive the necessary materials and documents related to the activities of the QCD controller.3.4. On the instructions of the head of the quality control department, enter into relationships with divisions of third-party institutions and organizations to resolve operational issues of production activities.4.
RESPONSIBILITY. The quality control inspector is responsible for: 4.1.

Job description of the control master of the technical control department

Product quality control, separation of parts of products that have defects. 2.18. Monitoring the correct sorting of products into batches and assortments.
2.19. Inspection and acceptance in accordance with design documentation and technical specifications of complex configurations of products made from various plastics and rubber. 2.20. Inspection and acceptance of small items using magnifying glasses and a microscope.

2.21. Checking the geometric shape and relative position of surfaces, participating in various tests. 2.22. Organization of additional control of the technological process in order to eliminate the reasons that caused its violation.
2.23. Drawing up a diagnostic file that provides possible options for influencing the technological process in case of deviations of its parameters or indicators of raw materials from those established by the norm. 2.24.

Job description of the opening foreman

The incoming inspection controller reports directly to the head of the quality control incoming control bureau.1.4 The incoming quality control inspection controller is appointed and dismissed by the head of the quality control department on the recommendation of the head of the quality control incoming control bureau.1.5 The incoming quality control inspection controller in his work is guided by: - ​​this job description; - the standard of the STP enterprise QMS 7-011 “Incoming inspection”; - technological statement BI.70002.00001 “Materials, semi-finished products and components subject to incoming inspection”; - technological instructions for incoming inspection; - labor protection rules; - internal labor regulations of the enterprise; - fire safety rules safety; - enterprise quality policy; - QMS documentation necessary to perform the work. 2.

Info

Requirements for a Quality Control Inspector The main requirements for a Quality Control Inspector are as follows:

• Secondary technical or higher education.
• Experience from 1 year.
• Knowledge of production technology, GOST standards.
• Ability to read drawings and design documentation.
• Skills in operating control and measuring instruments.
• Attention to detail.

Sometimes a specialist may be required to have good vision and excellent coordination of movements, as well as additional education (depending on the specifics of the production). Sample resume Sample resume for Quality Control Controller. How to become a quality control inspector To become a quality control inspector, it is enough to receive a secondary technical or higher specialized education.

Knowledge of production processes is also necessary, because the specialist communicates with technologists, designers, craftsmen, heads of production departments and the sales department.

Profession inspector

Responsibility The 6th category product and process quality controller is responsible for: 5.1. For non-fulfillment or improper fulfillment of the duties provided for in these instructions - within the limits determined by the labor legislation of the Russian Federation.

For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal, and civil legislation of the Russian Federation. 5.3. For causing material damage to the employer - within the limits determined by the current labor and civil legislation of the Russian Federation.

The job description has been developed in accordance with [name, number and date of document].

Rights of the incoming control inspector QTC 4.1 The incoming control inspector has the right to: - enjoy the benefits provided for in the collective agreement of the enterprise; - demand that TSU employees comply with the rules and requirements for the storage and delivery of materials and components to the workshops; - demand the provision of working conditions to perform assigned duties .- Make conclusions about the quality of received materials, raw materials and components that are mandatory for the TSU. 5. Responsibility of the incoming quality control inspector The incoming inspection controller is responsible for: - failure to fulfill the tasks assigned to him and the responsibilities provided for by this job description and the employment contract; - non-compliance with labor protection and safety regulations.

Industrial sanitation and fire safety. Head of Quality Control Department Agreed by: Head of HR Department Head of Maintenance Department Deputy.

Important

Studying and improving technology for monitoring products, materials, and components. Participation in events related to the introduction of new and revision of existing standards, technical specifications, regulations, quality indicators and instructions.

3.

RIGHTS The Quality Control Master has the right: 3.1. Request and receive the necessary materials and documents related to the activities of the QCD master. 3.2. Enter into relationships with departments of third-party institutions and organizations to resolve operational issues of production activities that are within the competence of the quality control specialist.

RESPONSIBILITY The Quality Control Master is responsible for: 4.1. Failure to fulfill one's functional duties.

4.2. Inaccurate information about the status of the work. 4.3. Failure to comply with orders, instructions and instructions of the Head of the Organization. 4.4.

Job description of quality control controller for the production of polyethylene film

During the period of temporary absence of the QCD master, his duties are assigned to. 2. FUNCTIONAL RESPONSIBILITIES 2.1. The quality control master carries out: Taking measures to prevent production and preventing the release of products that do not meet established requirements, identifying the causes and culprits of the defect, organizing the recording of defects.

Work on the preparation of technical documentation certifying the quality and completeness of the supplied products (passports, certificates, etc.). Participation in the delivery of finished products and completed work (services) to customers. Verification of compliance with instructions and methods for technical control at workplaces. Quality control of containers and packaging at workplaces, technical condition of equipment and means of transport, storage of raw materials, materials, semi-finished products, components, finished products.